Super Weapon Swap System

3The motherland is growing, and every industry needs precision processing so they can come to our side and ask for support.     3

    

Hearing Qin Guan's words, Worker Zhang, who was standing at the side, couldn't help but nod his head. He was too grateful!    

    

For the 114 Institute, they needed to overcome the difficulty of the Flat Gap Radar antenna. They needed precise processing techniques. However, if the 114 research institutes were to bring in the corresponding processing tools... That would cause a huge waste because they were the ones who produced the radar equipment. The main production of electronic products required very little precision processing. Directly bringing in one, the production was only a few dozen radars that year. It was too wasteful.    

    

It would be best if they could find a special place to process it.    

    

At the same time, in China, people who knew how to operate the Five axis Connection Cnc Machine Tool... There were no such people. Even Sandra needed to be studied and pondered over. Marriage was more beneficial to the country. By using Hee Ribala to tie her down, she would be able to serve the country.    

    

Hee Ribala did not lose anything. He married a foreign wife. He looked at her figure and her breasts. Tsk tsk. Hee Ribala would definitely feel good about it.    

    

Now, the Cnc Machine Tool industry in the country had not developed yet. This could not be helped. It had to go through a process. There were also very few people who could operate the machine tools. Otherwise, he wouldn't have thought about Sandra.    

    

However, this could be considered a win-win cooperation. In the Steyr Company, where would there be a heavy truck company in the north? It could bring out her talent even more.    

    

Through this processing center, it would greatly improve the high precision processing ability in the country, and it would be a great help to the development of the country.    

    

For example, in the production process of this engine, some precision parts could actually be handed over to their own side to process. They could improve the process and increase efficiency.    

    

Another example would be their own heavy truck. Now, it was time to make slight improvements. One of the most important aspects was to use a supercharge.    

    

"Wait until your wedding ends. Our factory... There's still a new project to be carried out. " Qin Guan continued, "The engine that we are using right now belongs to the natural breathing engine. We need to improve it further and dig out its potential. Turn it into a pressurized engine. "    

    

In the future, whenever turbine hydraulic engines were mentioned, there would be a group of experienced drivers who were disgusted. They said that power was not linear, that life expectancy was low, and so on. He felt that he was very knowledgeable, that they did not know at all. In the field of trucks, the turbine hydraulic device had long entered the range of usage.    

    

Now, the Han Country's own heavy truck project was many years ahead of history. Therefore, what was currently equipped on the heavy truck was just a copy of the Start 991 series's WD615.00 engine, which was the basic model of the WD615 series. Usage: Nature Breaker Design: Power of 200 horsepower, can output 623N when it turns 1400 / minutes. M's torque.    

    

At the same time, it can also change the power of the engine by changing the launch system, but the change is limited. Even so, this engine is the most advanced engine in the country.    

    

Without the five-axis connecting Cnc Machine Tool, it was impossible to process the appropriate turbine pressure increasing leaf. Therefore, at that time, he did not consider the amplifier.    

    

The principle of the so-called amplifier was actually very simple. It was two linkage fans. One of the fans was driven by the exhaust gas that was discharged. In any case, the exhaust gas was useless. It was used to blow the turbine leaf. At the same time, the leaf was blown by the wind. It would move another leaf that was spinning in the same axis. This leaf... It was used to blow on the engine. This way, in the same displacement situation... The inside of the engine cylinder will be able to breathe in more air. It could shoot out more fuel, which would give it more power. It was that simple.    

    

As for its lifespan, in the future, it was almost as long as the engine. There was no need to worry. The use of new technology would always be resisted by some conservative people. With his own experience, he spoke frankly and frankly, but the promotion of new technology... It would not be affected by these people. Look at the future. Although it was boycotted, the turbine hydraulic engine became more and more mainstream. As for the heavy trucks, they were all turbine hydraulic.    

    

And on the Start's engine, this kind of improvement was also continuing, including the WD615. 61 was in the WD615. On the 500, an abandoned turbine amplifier was installed, and it was modified to increase the jet capacity.    

    

After some simple modifications, the power of this engine was increased from 200 horsepower to 260 horsepower. At 1600 revolution points, it could output 829N. M's torque. From the characteristic curve on it, it could be seen that it had only been slightly altered. The WD615.61's parameters were all better than the WD615.00, which showed the potential of the WD615 series engine.    

    

Therefore, it was already a trend to add the power amplifier to the engine. Of course, even the Steyr Company was only trying to do this. They had not completed the development of the model. Now, if they were to modify it in the country... They were already standing at the same starting line.    

    

However, this turbine hydraulic device couldn't be produced in the country.    

    

There were many manufacturers of the amplifier, such as Hans Country's KKKK 28, Cattle Country's Holset H2C, Y Country's Garrett 45. At that time, there were also counterfeits in the country, such as East Peace's GJ80, Hong Yuan's imitation of KKK 28, Wuxi power J90, and so on.    

    

However, the performance of these amplifiers was not good. In the end, Holset's amplifiers' flow range, highest speed, and compression ratio were all better than other manufacturers, and they were widely used.    

    

In the future, some manufacturers made their own engines and publicized it. We used some world-famous amplifiers, but in fact, there were almost no domestic ones. All of them were imported goods.    

    

It was impossible to produce advanced turbine hydraulic devices. On the one hand, it was because the shape of the turbine leaf inside was very special and couldn't be processed in China. On the other hand, the turbine turbine turbine easily exceeded ten thousand revolutions. Without a high-performance bearing, it could not withstand it at all. All of these required advanced processing equipment.    

    

Now that they had it, it was a piece of cake for them to produce the turbine amplifier. If they started research and development now, they might even be able to sell the turbine amplifier they produced all over the world in the future!    

    

Only by relying on the strength of the industry could the country be truly powerful. They could create advanced products and sell them all over the world. They could only rely on real estate to increase the fart of the so-called chicken.    

    

Qin Guan inexplicably thought of the future.    

    

Now, he heard Qin Guan say that he was going to transform it into a turbine to increase pressure. Sandra immediately expressed his agreement. "That's right. This is the trend of the heavy truck industry in Europe. If there is a five-axis linked Cnc Machine Tool, then... We will definitely be able to produce it!"